2004 (04) FORD Escape Car Stereo Installation Kit ALL stereo installation products on this site are manufactured in the USA. All shipping FREE

 2004 (04) FORD Escape Dash Install Kit

View Mobile Version of this page Back HomeView CartContact Us  
Happy Holidays - %10 off all orders!
 2004 (04) FORD Escape Car Stereo Installation Kit


 Below are the individual pieces that come in the car stereo installation kit(s)
 Car Stereo Mounting Kit  Car Stereo Mounting Kit  Wire Harness  Antenna Adapter
Not Available Not Available View Wire Harness Not Available
Not Available
Car Stereo install faceplate / mounting bracket not available.
Not Available
Car Stereo install faceplate / mounting bracket not available.
This Wire Harness will greatly simplify any car stereo installation. It will match up color for color to the wire harness of your aftermarket stereo
Not Available
Car Stereo install antenna adapter not available.
 Radio Replacement Interface With Navigation Outputs for Select Ford, Lincoln, Mercury Vehicles
Radio Replacement Interface With Navigation Outputs for Select Ford, Lincoln, Mercury Vehicles
Provides navigation trigger wires and timed accessory output for replacing the factory radio. Retains the factory installed amplified audio system and rear seat entertainment (if equipped). Use with a steering wheel interface module to retain function of all factory controls.
  • Compatible with THX, SONY, Shaker and Audiophile sound systems in applicable vehicles. (v1.1.4 or higher required)
  • Data controlled RAP accessory output wire
  • Data controlled parking brake wire
  • Data controlled reverse trigger wire
  • Data controlled vehicle speed sense wire
  • Data controlled illumination output wire
  • Retains factory-installed amplified audio system
  • Retains rear seat entertainment and dual zone audio
  • When installing the #3650 into 2009 Ford/Lincoln/Mercury vehicles that are equipped with the mid-line amplifier (NOT the Sony or THX system), you MUST follow a tech brief to turn the amplifier on (please see Tech Brief PDF below)
  • Rear seat entertainment (RSE) audio is not retained through the speakers in Ford/Lincoln/Mercury vehicles that are equipped with the Microsoft SYNC system. The RSE will power up, operate normally and pass audio through the IR headphones, however the audio can not be passed through the aftermarket radio.
  • Does not retain SYNC
  • Does not retain any of the radio related Ford "MyKey" features found in the 2011 vehicles
  • If you are installing the #3650 in any of the following vehicles, the revision number of the interface MUST be 1.1.4 in order to be compatible:
    2009 Ford F-150
    2009 Ford Flex
    2010 Ford Mustang
    2010 Ford Fusion
    2009 Lincoln MKS
    2010 Lincoln MKZ
    2010 Mercury Milan
  • 2008 F-250/350/450: Not compatible with model trim XL (fleet vehicles). These vehicles do not have the necessary CAN bus signals
  • 2006-2007 Ford Freestyle: Does not retain RSE
  • 2006 Lincoln Zephyr: Does not retain the THX amplifier
Instructions: Pdf Instruction Manual Pdf Tech Brief
 Need a replacement harnesses for your aftermarket stereo? Click Here
 Factory Stereo Removal Tool
Ford, Mazda & Blaupunkt Stereo Removal Tool
Ford, Mazda & Blaupunkt Stereo Removal Tool
If your factory stereo has four small holes, 2 on each side, this tool will be needed to properly remove the stereo.
 9-PC Soft Silicone Dash Removal Tools Set
Soft Silicone Dash Removal Tools
Dash Removal Tools
Some stereo installations may require that parts of the dash be removed. These clear soft silicone tools are made specifically for high end installations.
Helps elimiate scratches and chips!
 Factory System Integration - Add an Amp or Aftermarket Stereo
Premium Factory Sound Systems Integration
For the installation of aftermarket stereo, or amplifier integration into a vehicles pre-existing factory system.
The #5065 is a one-device solution for today's vehicle sound systems. It features programmable input and output circuitry with slide switches, which allows connection of RCA level or speaker level input and output. DC coupling circuit ensures noise free integration and no load induced on the factory system. This is in contrast to a normal LOC which uses resistors and can stress a factory radio's circuitry.
The #5065 utilizes signal sense to detect when audio is present in the device, and creates a 12V output usable for triggering an external amplifier.
  • Designed to be connected in the rear of the vehicle for quick installation
  • Provides 12v amplifier turn-on trigger wire
  • Linear 20 to 20,000Hz output based on input signal
  • Transformer isolated for optimal sound and performance
  • Maintains correct phasing
  • 60 watts maximum input per channel
Instructions: Pdf Instruction Manual
 Factory Speaker Information - Size & Location
 Front Speaker Size & Location:  6x8E
 Rear Speaker Size & Location:  6x8
 A. Top Dash C. Kick Panel E. Lower door G. Lower rear I. Rear side panel K. Rear sides M. Rear Door (Wagons, Vans) O. Rear Posts (Trucks)B. Front Dash D. Upper Door F. Behind Seat (Trucks) H. Upper Rear J. Rear deck L. Tall sides N. Rear Top (Wagons, Vans) P. Rear Corner (Trucks)
My Install Kit is a registered Trademark All Rights Reserved. My Install Kit cannot be responsible for errors published online. Some information published has been provided by manufacturer's and or corporations. My Install Kit tries to maintain accuracy. My Install Kit recognizes all manufacturer's trademarks and or trade names herein and disclaims any proprietary interest in their use. Copyright My Install Kit © 2014

Car Audio Aftermarket Stereo Installation Kits - Faceplates, Wire Harnesses, Antenna Adapters & PAC aftermarket car audio installation accessories! Car Audio Aftermarket Stereo Installation Kits for most vehicles Don't worry about wiring up that new stereo, with a car stereo installation kit everything is a snap!